Duerkopp Adler HP Series Additional guide Bedienungsanleitung PDF herunterladen (Seite 66)

EFKA AB220A/320A FP220A/320A

Operator Level

Parameter Designation Unit max min Preset Ind.

019 -Pd 0 = Pedal in pos. –1 disabled in the seam. With pedal in 4 0 3 *) A/A/A/A

pos. –2 in the seam, only sewing foot lifting is

possible. (Function only if parameter 009 = 1)

1 = Pedal in pos. –1, sewing foot lifting disabled in the

seam.

2 = Pedal in pos. –2, thread trimming disabled.

(Function only if parameter 009 = 1)

3 = Pedal in pos. –1 and –2 enabled in the seam.

4 = Pedal in pos. –1 and –2 blocked in the seam.

(Function only if parameter 009 = 1)

020 kLM Clamp at the seam end On/Off 1 0 0 A/A/A/A

021 ckL Run-out stitches clamp at the start of the seam stitches 254 0 2 *) A/A/A/A

022 SPo 0 = Chain suction until the end of count c2 2 0 0 A/A/A/A

1 = Chain suction at the seam end until pedal in

pos. 0 (neutral)

2 = Chain suction until the drive is at standstill

and the switch-off delay (parameter 237) has

elapsed

023 AFL Automatic sewing foot lifting with pedal forward 1 0 1 A/A/A/A

at the seam end, if light barrier or stitch counting is On

0 = Automatic sewing foot Off

1 = Automatic sewing foot On

024 FSP Coupled thread tension release and sewing foot lift. 3 0 0 C/C/C/B

The function can be activated only with a thread

trimmer that depends on the angle.

(Modes 3, 13, 20, 22, 23, 25)

0 = No coupling

1 = Coupled thread tension release and sewing foot

at the seam end with thread trimmer off.

2 = Coupled thread tension release and sewing foot

in the seam and at the seam end with thread

trimmer off.

3 = Coupled thread tension release and sewing foot

always effective.

025 tFS Start counting (pa. 157) for thread tension release 1 0 1 A/A/A/A

at the start of the seam

0 = Start counting at the start of the seam

1 = Start counting when the light barrier is covered

030 rFw 0 = Bobbin thread monitor Off 6 0 0 A/A/A/A

1 = Bobbin thread monitor with stop

2 = Bobbin thread monitor without stop

3 = Bobbin thread monitor with stop and start

blockage after thread trimming

4 = As 1, but display of remaining stitches

5 = As 2, but display of remaining stitches

6 = As 3, but display of remaining stitches

031 cFw Number of stitches for bobbin thread monitor stitches 25500 ***) 0 0 A/A/A/A

035 UFw 0 = External bobbin thread monitor Off 2 0 0 F/F/F/E

1 = Bobbin thread monitor with stop after stitch

counting (prameter 036)

2 = Bobbin thread monitor without stop

036 cUF Number of stitches for Juki bobbin thread stitches 5000 **) 0 0 F/F/F/E

monitor

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit

value displayed must be multiplied by 10.

***) When programming the 5-digit (max) parameter values on the control or control panel, the 3-digit value displayed

must be multiplied by 100.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 87 88

Kommentare zu diesen Handbüchern

Keine Kommentare

Duerkopp Adler HP Series Additional guide Bedienungsanleitung Seite 66

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nähmaschinen Duerkopp Adler HP Series Additional guide