Duerkopp Adler 910 Bedienungsanleitung

910CNC-Nähanlage für freie NahtkonturenCNC sewing unit for free seam contoursBedienanleitung / Operating InstructionsAufstellanleitung / Installation

3.3 Completing the table top–Place the table top on a worktop upside down.–Screw the main switch 6 on the underside of the table top on theleft.–Screw

–Place the control box 8 on the underside of the table top andposition it in such a way that the side with the four sockets points tothe left (towards

3.4 Connecting the control box to the main switchATTENTION !Work of every kind on the electric equipment of the sewing unit mustonly be carried out by

3.5 Mounting the stand and the reference value transmitter–Put the stand on the table top and screw it tight.–Screw the set value initiator 1 with the

3.6 Mounting the oil collector sump–Insert the holder for the oil collector sump in the drill-hole of thetable top.–Screw the oil collector sump 1 in.

3.7 Adjusting the working heightThe working height is adjustable between 750 and 950 mm (measuredup to the top edge of the table top).–Loosen the scre

4. Mounting the sewing unit4.1 Mounting the oil pan–Lay the oil pan 1 on the table top 3, align it and screw it tightthrough the two through-bores 2 w

4.2 Assembly of the sewing unitThe small parts for setting up the sewing unit are included in theaccessories.–Place the sewing unit 1 on the oil pan 4

4.3 Mounting the control panel–Screw the control panel 4 on the sewing unit with angle 3.Lay rubber washers between the mounting angle of the controlp

4.4 Potential compensation–From the control 1 to the machine head 2–From the machine head 2 to the oil pan 3152321

Alle Rechte vorbehalten.Eigentum der Dürkopp Adler AG und urheberrechtlich geschützt. Jede, auch auszugsweiseWiederverwendung dieser Inhalte ist ohne

4.5 Mounting the cover hood–Place the cover hood 2 on the fitting spring 4 from above.–Lay the cable 3 of the control panel in the gap 5 of the cover

5. Connecting the plug connections to the control box5.1 Plug connections at the multiple pin strip (4-fold)Connect the plug connections of the sewing

5.2 Plug connections at the multiple pin strip (15-fold)Connect the plug connections of the sewing unit, the c ontrol panel andthe reference value tra

5.3 WiringIn order to make it possible to tilt the machine head back the cablesleading from the head through the opening in the table top either to th

7. Changing the sewing foot and the fabric clampsThe sewing unit 910 is delivered with two sewing feet.Caution: Risk of injury !Switchthemainswitchoff

8. Mounting the eye protectionCaution: Risk of injury !The sewing unit must not be operated without eye protection.–Tighten the eye protection 1 at th

9. Oil lubricationCaution: Risk of injury !Oil can cause skin eruption.Avoid a longer contact with the skin.Wash yourself thoroughly after a contact.A

9.2 Oiling wicks and felt part (connecting rod)ATTENTION !When assembling the machine and after longer idle times the wicksand the felt part 1 have to

9.3 Oiling the hook pathOiling the hook path–Flap down the hook cover.–Give a drop of oil between driver 2 and path 1.–Close the hook cover.ATTENTION

10. Putting into operation10.1 Installation of the machine software10.1.1 General notesWith the help of the “dongle with program” a specific sewing so

ForewordThis instruction manual is intended to help the user to become familiarwith the machine and take advantage of its application possibilities in

–Pull the dongle 2 out now.ATTENTION !The software must be compatible with the machine class.If the software version does not correspond to the machin

10.2 Seam programIf no seam program is stored in the control, the following message willbe indicated when the sewing unit is switched on for the first

10.3 Sewing testAfter finishing the assembly work a sewing test should be made.–Plug the mains plug in.–Wind up the bobbin thread (see operating instr

11. Optional equipment11.1 Sewing lampFor the sewing unit 910 the sewing lamp 1 (order no.9822 510026) and the table clamp 3 (order no. 9822 510027) a

Note:30

General safety instructionsThe non-observance of the following safety instructions can cause bodily injuries or damages to the machine.1. The machine

Index Page:Part 2: Installation Instructions cl. 9101. Scope of delivery... 32. General notes and securing

213108762549

1. Scope of deliveryThe scope of delivery is dependent on your order.Please check before the assembly whether all required parts areavailable.This des

Punch-marks from the underside1 x on this spot only4 punch-marks fordrywall screws4

3. Mounting the stand and the control cabinet3.1 Table topsThe cutouts of self-manufactured table tops must have the dimensionsindicated in the sketch