Duerkopp Adler 527-105 Bedienerhandbuch

Instruction manual527Minerva Boskovice, a.s., Sokolská 60, CZ - 680 17 BoskoviceTel.: +420-516-453434, 453433, 494111 Fax: +42

67. Machine maintenanceCaution!Before cleaning and lubricating the machine switch off the main switch and put your your feet off the pedals on thesta

78. Electronic control of the machine(it is valid for sub-classes equipped with stop motor)8.1 Control of sewing by means of control elements8.1.1 V

88.2 Adjustment of automatic functions via controlpanel for stop motor8.2.1 By using stop motor Efka with panel V 810(Fig 16)Functioning pushbutton

9Foot position adjustment by stopping at the seam (by neutralposition of treadle) and after finishing seam (by neutral posi-tion of treadle):Setting i

10ABCD E F GHI JKLMNOPQON/OFF thread trimmer:No. of parameter Value range Descriptionof parameter of parameters013 ON/OFFThread trimmerON/OFF8.2.2 By

118.2.2.1 Adjustment by means of buttons with fixed settingfunction (Fig. 17)Note: It is important to finish the seam in order to reacheffective but

12Note: 1. For permanent memory storing of changed pa-rameter, it is necessary to press treadle forwardsdown after changing of parameters.2. Mode of

13Trouble1. Machine runs with difficulty.2. Machine starts with slow running.3. Upper thread tearing.4. Lower thread tearing.5. Skipping of stitches.6

146.2 Negligent sewing, pulling of thematerial.6.3 Needle too thin for thick material.6.4 Needle incorrectly mounted.6.5 Throat plate loosened.6.6 Upp

1514. Low quality of stitch start on rearside.15. No upper or lower thread trimming.16. No upper and lower thread trim-ming, but machine rotates froml

Contents - part A - Instruction manual:1. Proper use of the machine ...

Contents - part B - The instructions for assembling:1. Safety instructions ...

1Part B - Instructions for assembling1. Safety instructionsCaution!The assembly of the machine is to be done only by a trained mechanician.All ope

2Fig. 1Motors are to be chosen according to the following table:* Control panel S359 600038/V810 or S359 600050/V820 it is possible to order for setti

3Fig. 2Fig. 4Fig. 3AB162005701352137648

4Fig. 5323 x THREADED INLAY M8 SCREWED INTO HOLES ø 14; DEPTH 30GG

5Fig. 65. Assembly and screwing on of the stand table top5.1 Assembly of stand table top (Fig. 2, 3, 4, 5)Put the rubber inserts for placing the mach

66. Mounting of a position reader and of a control panel of the stop motor (Fig. 7, 8)Put the position reader (2) on the pin of the hand wheel in suc

7123Fig. 13Fig. 148. Mounting of the equipment for backward stitching (Fig. 11, 12)Remove the backward stitching lever and the knob for setting the s

810. Composition and assembly of the thread stand (Fig. 15, 16)Assemble the thread stand and mount it into the hole in the plate so that its arms woul

9Circuit layout - EvropaCircuit layout - AmerikaTransformer for sewing area bulbMachine standMachine headTransformer for sewing area bulbMachine s

ForewordThis instruction manual is intended to help the user to become familiar with the machine and take advantage of its applicationpossibilities in

10Circuit layout - EvropaCircuit layout - Amerika12.2 Power supply 3 x 400 V - five wire power distribution, power supply 3 x 230 V - four wire orfiv

1112.4 Electrical connection of machine head to the stop motorCircuit layoutStop motor S359 600045 XXX - EFKA DC 1600/DA82GA

12Stop motor S359 600052 XX - EFKA VD 552/6F82FACircuit layout

132 A1 A1212.5 Stop motor setting S359 600045 XXX - EFKA DC 1600/DA82GA12.5.1 Setting position reader- set the parameter 170, the display will show

1412.6.2 Changes in parameters of stop motor setting considering original producer settingParameter ParameterNo value111 Max. revolutions (according

General safety instructionsThe non-observance of the following safety instructions can cause bodily injuries or damages to the machine.1. The machine

1Part A - Instruction manual1. Proper use of the machineThe machine is designed mainly for sewing operations in the shoe manufacture for assembling

24.1.3 Optional equipmentS791 400023 Guide for sewing togetherS791 149001 Attachment for serging operationS791 430048 35 Bead stitching - needle dista

36. Operation of the machineCaution!Do not use this sewing machine without using the finger guard(C, Fig. 4) and without the take-up lever guard (P,

46.4 Adjustment of the upper thread tension(Fig. 1, 2, 5)The tension of the upper and that of the bottom thread must bemutually adjusted in such a

56.6 Adjustment of the stitch length, reverse stitching(Fig. 8, 9)The stitch length is changed in turning the knob (A), which isplaced on the arm we